Skip to main content

Satellite Communication - Launching

Satellites stay in space for most of their life time. We know that the environment of weightlessness is present in the space. That’s why satellites don’t require additional strong frames in space. But, those are required during launching process. Because in that process satellite shakes violently, till the satellite has been placed in a proper orbit.
The design of satellites should be compatible with one or more launch vehicles in order to place the satellite in an orbit.
We know that the period of revolution will be more for higher apogee altitude according to Kepler’s second law. The period of geostationary transfer orbit is nearly equal to 16 hours. If perigee is increased to GEO altitude (around 36,000 km), then the period of revolution will increase to 24 hours.

Launching of Satellites

The process of placing the satellite in a proper orbit is known as launching process. During this process, from earth stations we can control the operation of satellite. Mainly, there are four stages in launching a satellite.
  • First Stage − The first stage of launch vehicle contains rockets and fuel for lifting the satellite along with launch vehicle from ground.
  • Second Stage − The second stage of launch vehicle contains smaller rockets. These are ignited after completion of first stage. They have their own fuel tanks in order to send the satellite into space.
  • Third Stage − The third (upper) stage of the launch vehicle is connected to the satellite fairing. This fairing is a metal shield, which contains the satellite and it protects the satellite.
  • Fourth Stage − Satellite gets separated from the upper stage of launch vehicle, when it has been reached to out of Earth's atmosphere. Then, the satellite will go to a “transfer orbit”. This orbit sends the satellite higher into space.
When the satellite reached to the desired height of the orbit, its subsystems like solar panels and communication antennas gets unfurled. Then the satellite takes its position in the orbit with other satellites. Now, the satellite is ready to provide services to the public.

Satellite Launch Vehicles

Satellite launch vehicles launch the satellites into a particular orbit based on the requirement. Satellite launch vehicles are nothing but multi stage rockets. Following are the two types of satellite launch vehicles.
  • Expendable Launch Vehicles (ELV)
  • Reusable Launch Vehicles (RLV)

Expendable Launch Vehicles

Expendable launch vehicles (ELV) get destroyed after leaving the satellites in space. The following image shows how an ELV looks.



The ELV contains three stages. First and second stages of ELV raise the satellite to an about 50 miles and 100 miles. Third stage of ELV places the satellite in transfer orbit. The task of ELV will be completed and its spare parts will be fallen to earth, when the satellite reached to transfer orbit.

Reusable Launch Vehicles

Reusable launch vehicles (RLV) can be used multiple times for launching satellites. Generally, this type of launch vehicles will return back to earth after leaving the satellite in space.
The following image shows a reusable launch vehicle. It is also known as space shuttle.
The functions of space shuttle are similar to the functions of first and second stages of ELV. Satellite along with the third stage of space shuttle are mounted in the cargo bay. It is ejected from the cargo bay when the space shuttle reaches to an elevation of 150 to 200 miles.
Then, the third stage of space shuttle gets fired and places the satellite into a transfer orbit. After this, the space shuttle will return back to earth for reuse.
Labels:

Comments

Post a Comment

Popular posts from this blog

Design Engineer at Infineon Bangalore

  Hello Dear Readers, Currently at Infineon Bangalore vacancy for the Design Engineer role. Design analog and mixed-signal modules in CMOS and Smart PowerTechnologies, with a particular focus on achieving high-efficiency power conversion for applications using GaN devices; In your new role you will: Design analog and mixed-signal modules  in CMOS and Smart PowerTechnologies, with a particular focus on achieving high-efficiency power conversion for applications using GaN devices; Design and verify pre-silicon analog/mixed-signal integrated circuit blocks, including incorporating features for testing and quality assurance, and providing support for top-level integration; Assist in defining the requirements  for analog and mixed-signal blocks,aligning them with IP Module architecture, and ensuring compliance with requirements through documentation; Estimate effort and planning design work packages to meet project milestones; Provide essential support to physical design ...
1 comment
Read more

Engineer II - Analog Design Engineering at Microchip

Hello Dear Readers,   Currently at Microchip  vacancy for Engineer II - Analog Design Engineering role. Job Description: The Mixed Signal Development Group is responsible for delivering analog, digital and mixed-signal IP to divisions within Microchip. We work with leading edge CMOS processes to produce analog integrated circuits for wireline applications. From 112Gb/s+ SERDES to high-speed FEC engines, we enable technology that allows Microchip’s products to interface to the outside world.  Job Descriptions: As a member of the Mixed-Signal Development Group, the candidate will be supervised by a team leader/manager, and be engaged in the design of SERDES/DSP blocks, and other high-speed Digital Signal Processing blocks. This will involve taking a design from initial concept to production form. Throughout you will be mentored and coached by experienced engineers and be exposed to Microchip's Best-In-Class engineering practices. Job Responsibilities: Ramping up o...
2 comments
Read more

Analog Design Engineer II at onsemi

Hello Dear Readers,   Currently at onsemi  vacancy for  Analog Design  Engineer II role. JOB DESCRIPTION: An analog design engineer is expected to quickly take an analog design block through all phases of the development process, including design, simulation, and supervision of the layout/verification processes and evaluation/debug of silicon samples. A Senior Analog IC Design Engineer will be responsible for individual block designs using CMOS process. That person will work with the latest Cadence analogue design tools (Virtuoso Composer, Verilog) Spectre and appropriate PC-based tools (MATLAB). The nature of the circuits is Mixed Signal involving blocks such as switched capacitor amplifiers, data converters, charge pumps, references, voltage buffers, IO circuits and digital building blocks. QUALIFICATIONS: Analog engineer is expected to have PhD (no experience) or master’s degree in field of Electrical Engineering/VLSI/Electronics with 0-2 years of experience and w...
1 comment
Read more